SNAP TEX Cables
About SNAP TEX Cables
SNAP TEX cables provide convenient connections from I/O modules to field wiring. Most cables are designed to connect to breakout boards; some cables have flying leads for direct connection to field devices.
View all SNAP TEX Cables
SNAP-HD-20F6
The SNAP-HD-20F6 cable is designed for use with an 8-channel SNAP-AOVA-8 analog output module. The cable has a 20-pin connector at the module end and flying leads for field wiring. Use with SNAP-AOVA-8 analog output module
20-pin connector at module, flying leads for field wiring.
High Density Wiring Harness, 20 conductors, Flying leads, 6 feet in length.
SNAP-HD-G4F6N
The SNAP-HD-G4F6N header cable connects a SNAP-IDC-32N high-density digital input module to two G4 digital I/O racks. This allows older G4 (or even G1) digital output systems to be integrated with modern Opto 22 products like SNAP PAC controllers, SNAP Ethernet-based brains, and PAC Project software.
The SNAP-HD-G4F6N connects one SNAP-IDC-32N with two G4PB16H, G4PB16HC, PB16H, or PB16HC racks. All G4 or G1 modules on the rack must be of the same type (input) and of the same logic voltage (15 or 24 VDC). Five-volt G4 modules cannot be used.
Header cable for SNAP-IDC-32N modules and G4 digital racks, 6 ft. (1.8 m).
SNAP-TEX-CB06
Part of the SNAP TEX family of mounting and wiring accessories, the SNAP-TEX-CBO6 cable provides neat, protected wiring from the top of a SNAP I/O module to a SNAP TEX breakout board. The cable is six feet (1.8 m) long.
Installation, maintenance, and troubleshooting are faster and simpler using SNAP TEX cables. Each cable snaps into the top of one module and terminates at the breakout board with 18-gauge, color-coded flying leads, already stripped and ready for wiring. The leads attach easily to the breakout board with spring connectors.
8-wire Cable for SNAP I/O Modules, Odd Terminals Connected.
SNAP-TEX-CBE6
Part of the SNAP TEX family of mounting and wiring accessories, the SNAP-TEX-CBE6 cable provides neat, protected wiring from the top of a SNAP I/O module to a SNAP TEX breakout board. The cable is six feet (1.8 m) long.
Installation, maintenance, and troubleshooting are faster and simpler using SNAP TEX cables. Each cable snaps into the top of one module and terminates at the breakout board with 18-gauge, color-coded flying leads, already stripped and ready for wiring. The leads attach easily to the breakout board with spring connectors.6N connects one SNAP-IDC-32N with two G4PB16H, G4PB16HC, PB16H, or PB16HC racks. All G4 or G1 modules on the rack must be of the same type (input) and of the same logic voltage (15 or 24 VDC). Five-volt G4 modules cannot be used.
8-wire Cable for SNAP I/O Modules, Even Terminals Connected.
SNAP-TEX-CBS6
Part of the SNAP TEX family of mounting and wiring accessories, the SNAP-TEX-CBS6 cable provides neat, protected wiring from the top of a SNAP I/O module to a SNAP TEX breakout board. The cable is six feet (1.8 m) long.
Installation, maintenance, and troubleshooting are faster and simpler using SNAP TEX cables. Each cable snaps into the top of one module and terminates at the breakout board with 18-gauge, color-coded flying leads, already stripped and ready for wiring. The leads attach easily to the breakout board with spring connectors.
8-wire Cable for SNAP I/O Modules, Straight-through Wiring.
SNAP-TEX-ACF6
The SNAP-HD-ACF6 is a 6 ft. (1.8 m) wiring harness assembly for SNAP 16-channel digital input modules. The assembly attaches to the top connectors of a 16-channel digital module and provides flying leads for wiring to field devices.
Wiring harness assembly with flying leads for SNAP 16-channel I/O modules – 6 ft. (1.8 m).
SNAP-HD-G4F6
The SNAP-HD-G4F6 header cable has two uses: to connect a 32-channel digital module to older G4 digital I/O racks, and to connect a 32-channel digital output module to two SNAP-TEX-MR10-16C breakout boards in order to switch multiple loads up to 10 amps.
Header cable for SNAP 32-channel digital modules and G4 digital racks, 6 ft. (1.8 m).
SNAP-HD-BF6
The SNAP-HD-BF6 is a 6-foot (1.8 m) header cable for connecting a SNAP 32-channel digital or analog module to an appropriate breakout rack.
Header cable for SNAP 32-channel modules and breakout racks – 6 ft. (1.8 m).
SNAP-HD-CBF6
The SNAP-HD-CBF6 is a 6-foot (1.8 m) wiring harness for SNAP 32-channel digital and analog modules. The wiring harness attaches to the top of the 32-channel module and provides flying leads for wiring to field devices.
Wiring harness with flying leads for SNAP 32-channel I/O modules – 6 ft. (1.8 m).
