Digital SNAP I/O Modules
About Digital SNAP I/O Modules
Opto 22 SNAP I/O 4-channel digital input modules are part of the SNAP PAC System. Optical isolation on these modules provides 4,000 volts of transient (4000 V for 1 ms) protection for sensitive control electronics from industrial field signals. Digital input modules can sense either AC or DC signals.
All SNAP 4-channel digital modules have removable top-mounted connectors to provide easy access for field wiring, and all operate on 5 VDC control logic. Each digital module features integral channel-specific LEDs for convenient troubleshooting and maintenance. Each module is factory tested twice and is UL and CE approved.
AC Output SNAP Digital I/O Modules
SNAP-OAC5
The SNAP-OAC5 provides four channels of 12-250 VAC digital output, each switching a separate AC load. AC outputs use zero voltage turn on and zero current turn off for transient-free switching. The module has removable top-mounted connectors to provide easy access to field wiring and features channel-specific LEDs for troubleshooting.
SNAP 4-Ch 12-250 VAC Digital (Discrete) Output Module
SNAP-OAC5
| Key Feature | -- |
| Torque, hold-down screws | Not to exceed 1 in-lb (0.11 N-m) |
| Torque, connector screws | 5.22 in-lb (0.59 N-m) |
| Field Side Ratings (each channel) | |
| Line Voltage - Range | 12–250 VAC |
| Line Voltage - Nominal | 120/240 VAC |
| Current Rating 0 °C to 70 °C Ambient | 3 amps per module |
| One Cycle Surge | 80 amps peak (50/60 Hz) |
| Minimum Load Current | 20 mA |
| Output Voltage Drop | 1.6 volts max.@ 0.75 amps |
| Off-state Leakage at Nominal Voltage - 60 Hz | 2.5 mA @ 240 VAC 1.25 mA @ 120 VAC |
| Peak Blocking Voltage | 500 V |
| Operating Frequency | 25–65 Hz |
| dV/ dt - Off-state | 200 volts/msec |
| dV/ dt - Commutating | Snubbed for rated 0.5 power factor load |
| Fuse (Common to all Channels) | 250 VAC - 4A 5x20 mm Fast-acting Bell Fuse Part: BEL 5HF4 Opto 22 Part: SNAP-FUSE4AB |
| Channel-to-channel isolation | Not applicable |
| Logic Side Ratings | |
| Pickup Voltage | 4 V @ 5.5 mA |
| Dropout Voltage | 1 VDC |
| Control Resistance | 220 ohms |
| Logic Supply Voltage | 5 VDC ± 0.25 VDC |
| Logic Supply Current | 50 mA maximum |
| Module Ratings | |
| Number of Channels Per Module | 4 |
| Turn-on Time | 0.5 cycle maximum (zero volts crossover) |
| Turn-off Time | 0.5 cycle maximum (zero current crossover) |
| Isolation (Field Side to Logic Side) | 4,000 volts (transient) |
| Temperature | -20 ° to 70 °C, operating |
| -40 ° to 85 °C, storage | |
| Wire size range | 22 to 14 AWG |
| Agency Approvals | UL, CE, CSA, RoHS, DFARS; UKCA |
| Warranty | Lifetime |
SNAP-OAC5MA
The SNAP-OAC5MA provides four isolated channels of 12-250 VAC digital output, each switching a separate AC load. AC outputs use zero voltage turn on and zero current turn off for transient-free switching. The module features manual-on/manual-off/automatic switches that override output from the application and are ideal for testing field device wiring.
SNAP 4-Ch Isolated 12-250 VAC Digital (Discrete) Output Module with Manual/Auto Switches
SNAP-OAC5MA
| Key Feature | Diagnostic switches Four isolated channels |
| Torque, hold-down screws | Not to exceed 1 in-lb (0.11 N-m) |
| Torque, connector screws | 5.22 in-lb (0.59 N-m) |
| Field Side Ratings (each channel) | |
| Line Voltage - Range | 12–250 VAC |
| Line Voltage - Nominal | 120/240 VAC |
| Current Rating 0 °C to 70 °C Ambient | 3 amps per module |
| One Cycle Surge | 80 amps peak (50/60 Hz) |
| Minimum Load Current | 20 mA |
| Output Voltage Drop | 1.6 volts max.@ 0.75 amps |
| Off-state Leakage at Nominal Voltage - 60 Hz | 2.5 mA @ 240 VAC 1.25 mA @ 120 VAC |
| Peak Blocking Voltage | 500 V |
| Operating Frequency | 25–65 Hz |
| dV/ dt - Off-state | 200 volts/msec |
| dV/ dt - Commutating | Snubbed for rated 0.5 power factor load |
| Fuse (Common to all Channels) | Has four isolated channels. User must provide own fusing. |
| Channel-to-channel isolation | 300 VAC (1500 V transient) |
| Logic Side Ratings | |
| Pickup Voltage | 4 V @ 5.5 mA |
| Dropout Voltage | 1 VDC |
| Control Resistance | 220 ohms |
| Logic Supply Voltage | 5 VDC ± 0.25 VDC |
| Logic Supply Current | 50 mA maximum |
| Module Ratings | |
| Number of Channels Per Module | 4 |
| Turn-on Time | 0.5 cycle maximum (zero volts crossover) |
| Turn-off Time | 0.5 cycle maximum (zero current crossover) |
| Isolation (Field Side to Logic Side) | 4,000 volts (transient) |
| Temperature | -20 ° to 70 °C, operating |
| -40 ° to 85 °C, storage | |
| Wire size range | 22 to 14 AWG |
| Agency Approvals | UL, CE, RoHS, DFARS; UKCA |
| Warranty | 30 months |
SNAP-OAC5-i
The SNAP-OAC5-i provides four isolated channels of 12-250 VAC digital output, each switching a separate AC load. AC outputs use zero voltage turn on and zero current turn off for transient-free switching. The module features channel-specific LEDs for troubleshooting.
SNAP 4-Ch Isolated 12-250 VAC Digital (Discrete) Output Module
SNAP-OAC5-i
| Key Feature | Four isolated channels |
| Torque, hold-down screws | Not to exceed 1 in-lb (0.11 N-m) |
| Torque, connector screws | 5.22 in-lb (0.59 N-m) |
| Field Side Ratings (each channel) | |
| Line Voltage - Range | 12–250 VAC |
| Line Voltage - Nominal | 120/240 VAC |
| Current Rating 0 °C to 70 °C Ambient | 3 amps per module |
| One Cycle Surge | 80 amps peak (50/60 Hz) |
| Minimum Load Current | 20 mA |
| Output Voltage Drop | 1.6 volts max.@ 0.75 amps |
| Off-state Leakage at Nominal Voltage - 60 Hz | 2.5 mA @ 240 VAC 1.25 mA @ 120 VAC |
| Peak Blocking Voltage | 500 V |
| Operating Frequency | 25–65 Hz |
| dV/ dt - Off-state | 200 volts/msec |
| dV/ dt - Commutating | Snubbed for rated 0.5 power factor load |
| Fuse (Common to all Channels) | Has four isolated channels. User must provide own fusing. |
| Channel-to-channel isolation | 300 VAC (1500 V transient) |
| Logic Side Ratings | |
| Pickup Voltage | 4 V @ 5.5 mA |
| Dropout Voltage | 1 VDC |
| Control Resistance | 220 ohms |
| Logic Supply Voltage | 5 VDC ± 0.25 VDC |
| Logic Supply Current | 50 mA maximum |
| Module Ratings | |
| Number of Channels Per Module | 4 |
| Turn-on Time | 0.5 cycle maximum (zero volts crossover) |
| Turn-off Time | 0.5 cycle maximum (zero current crossover) |
| Isolation (Field Side to Logic Side) | 4,000 volts (transient) |
| Temperature | -20 ° to 70 °C, operating |
| -40 ° to 85 °C, storage | |
| Wire size range | 22 to 14 AWG |
| Agency Approvals | UL, CE, RoHS, DFARS; UKCA |
| Warranty | Lifetime |
AC Input SNAP Digital I/O Modules
SNAP-IAC5
The SNAP-IAC5 provides four channels of 90-140 VAC/VDC digital input. Each channel senses the on/off status for AC (or DC) voltages from sources such as proximity switches, push buttons, or auxiliary contacts. The module has removable top-mounted connectors for easy access to field wiring, as well as channel-specific LEDs for convenient troubleshooting.
SNAP 4-Ch 90-140 VAC/VDC Digital (Discrete) Input Module
SNAP-IAC5
| Key Feature | |
| Wire Size | 22 to 14 AWG |
| Torque, hold-down screws | Not to exceed 1 in-lb (0.11 N-m) |
| Torque, connector screws | 5.22 in-lb (0.59 N-m) |
| Field Side Ratings (each channel) | |
| Nominal Input Voltage | 120 VAC/VDC |
| Channel-to-channel isolation | 300 VAC (1,500 V transient) |
| Input Voltage Range | 90–140 VAC/VDC |
| Turn-on Voltage | 90 VAC/VDC |
| Turn-off Voltage | 35 VAC/VDC |
| Input Resistance | 169 K ohms (nominal) |
| Logic Side Ratings | |
| Logic Output Voltage | <.5 V max. (on) @ 2 mA sinking 2.7 V min. (off) @ 400 mA sourcing |
| Logic Supply Voltage* | 5 VDC ± 0.25 VDC |
| Logic Supply Current | 50 mA maximum |
| Negative True Logic Output Drive | TTL 74 Series = 1 UL, TTL 74LS Series = 5 UL |
| Module Ratings | |
| Number of Channels Per Module | 4 |
| Turn-on Time | 30 msec |
| Turn-off Time | 30 msec |
| Optical Isolation, Field to Logic | 4,000 volts (transient) |
| Temperature | -20 °C to 70 °C, operating |
| -40 °C to 85 °C, storage | |
| Agency Approvals | UL, CE, CSA, RoHS, DFARS; UKCA |
| Warranty | Lifetime |
| * When used with an I/O processor (brain or on-the-rack controller), the processor requires 5.0 to 5.2 VDC. | |
SNAP-IAC5A
The SNAP-IAC5A provides four channels of 180-280 VAC/VDC digital input. Each channel senses the on/off status for AC (or DC) voltages from sources such as proximity switches, push buttons, or auxiliary contacts. The module has removable top-mounted connectors for easy access to field wiring, as well as channel-specific LEDs for convenient troubleshooting.
SNAP 4-Ch 180-280 VAC/VDC Digital (Discrete) Input Module
SNAP-IAC5A
| Key Feature | |
| Wire Size | 22 to 14 AWG |
| Torque, hold-down screws | Not to exceed 1 in-lb (0.11 N-m) |
| Torque, connector screws | 5.22 in-lb (0.59 N-m) |
| Field Side Ratings (each channel) | |
| Nominal Input Voltage | 240 VAC/VDC |
| Channel-to-channel isolation | 300 VAC (1,500 V transient) |
| Input Voltage Range | 180–280 VAC/VDC |
| Turn-on Voltage | 180 VAC/VDC |
| Turn-off Voltage | 35 VAC/VDC |
| Input Resistance | 305 K ohms (nominal) |
| Logic Side Ratings | |
| Logic Output Voltage | <.5 V max. (on), @ 2 mA sinking, 2.7 V min. (off), @ 400 mA sourcing |
| Logic Supply Voltage* | 5 VDC ± 0.25 VDC |
| Logic Supply Current | 50 mA maximum |
| Negative True Logic Output Drive | TTL 74 Series = 1 UL, TTL 74LS Series = 5 UL |
| Module Ratings | |
| Number of Channels Per Module | 4 |
| Turn-on Time | 30 msec |
| Turn-off Time | 30 msec |
| Optical Isolation, Field to Logic | 4,000 volts (transient) |
| Temperature | -20 °C to 70 °C, operating |
| -40 °C to 85 °C, storage | |
| Agency Approvals | UL, CE, CSA, RoHS, DFARS;UKCA |
| Warranty | Lifetime |
| * When used with an I/O processor (brain or on-the-rack controller), the processor requires 5.0 to 5.2 VDC. | |
SNAP-IAC5MA
The SNAP-IAC5MA provides four channels of 90-140 VAC/VDC digital input. Each channel senses the on/off status for AC (or DC) voltages from sources such as proximity switches, push buttons, or auxiliary contacts. This module features manual-on/manual-off/automatic switches that override input from field devices and are ideal for testing control applications.
SNAP 4-Ch Isolated 90-140 VAC/VDC Digital (Discrete) Input Module with Manual/Auto Switches
SNAP-IAC5MA
| Key Feature | Diagnostic switches |
| Wire Size | 22 to 14 AWG |
| Torque, hold-down screws | Not to exceed 1 in-lb (0.11 N-m) |
| Torque, connector screws | 5.22 in-lb (0.59 N-m) |
| Field Side Ratings (each channel) | |
| Nominal Input Voltage | 120 VAC/VDC |
| Channel-to-channel isolation | 300 VAC (1,500 V transient) |
| Input Voltage Range | 90–140 VAC/VDC |
| Turn-on Voltage | 90 VAC/VDC |
| Turn-off Voltage | 35 VAC/VDC |
| Input Resistance | 169 K ohms (nominal) |
| Logic Side Ratings | |
| Logic Output Voltage | <.5 V max. (on), @ 2 mA sinking, 2.7 V min. (off), @ 400 mA sourcing |
| Logic Supply Voltage* | 5 VDC ± 0.25 VDC |
| Logic Supply Current | 50 mA maximum |
| Negative True Logic Output Drive | TTL 74 Series = 1 UL, TTL 74LS Series = 5 UL |
| Module Ratings | |
| Number of Channels Per Module | 4 |
| Turn-on Time | 30 msec |
| Turn-off Time | 30 msec |
| Optical Isolation, Field to Logic | 4,000 volts (transient) |
| Temperature | -20 °C to 70 °C, operating |
| -40 °C to 85 °C, storage | |
| Agency Approvals | UL, CE, RoHS, DFARS |
| Warranty | 30 months |
| * When used with an I/O processor (brain or on-the-rack controller), the processor requires 5.0 to 5.2 VDC. | |
SNAP-IAC-16
The SNAP-IAC-16 senses on/off status for 16 channels of 90-140 VAC/VDC input. The module features automatic counting and latching.
SNAP isolated 16-pt digital (discrete) input module, 90-140 VAC/VDC
SNAP-AIC-16
| Input Range | 90–140 VAC/VDC |
| Nominal Voltage Range | 120 VAC |
| Input Resistance | 300 K ohms |
| Logic Voltage and Current | 5 VDC ± 0.1 @ 150 mA |
| Input Arrangement | 16 isolated input channels |
| Channel-to-Channel Isolation | 250 V steady-state, 1500 V transient |
| Maximum Operating Common Mode Voltage | 250 V |
| Isolation: Field to Logic | 1500 V |
| Maximum Number of HDD Modules on One Mounting Rack | 16 |
| Indicators | None; use optional OptoTerminal-G20 diagnostic display. |
| ON Voltage | 90 VAC/VDC @ 0.3 mA |
| OFF Voltage | 40 VAC/VDC @ 0.135 mA |
| Torque, hold-down screws | Not to exceed 1 in-lb (0.11 N-m) |
| Torque, connector screws | 5.22 in-lb (0.59 N-m) |
| Polling time from I/O processor to module1 | 2–30 ms typical2 |
| Input Turn-On/Off Time | 15 ms turn-on time 20 ms turn-off time |
| Counting Frequency (DC input) | 0–25 Hz @ 50% duty cycle |
| Operating Temperature | -20 to 70 °C |
| Storage Temperature | -40 to 85 °C |
| Agency Approvals | UL, CE, RoHS, DFARS; UKCA |
| Warranty | Lifetime |
| 1 Affects turn-on and turn-off determination 2 Time varies based on the SNAP PAC I/O processor (brain or on-the-rack controller), processor configuration, and Ethernet host communication activity. | |
DC Input SNAP Digital I/O Modules
SNAP-IDC5
The SNAP-IDC5 provides four channels of 10-32 Volts DC or AC digital input. Each channel senses the on/off status for DC voltages from sources such as proximity switches, push buttons, or auxiliary contacts. The module has removable top-mounted connectors for easy access to field wiring, as well as channel-specific LEDs for convenient troubleshooting.
SNAP 4-Ch 10-32 VAC/VDC Digital (Discrete) Input Module
SNAP-IDC5
| Key Feature | -- |
| Wire size | 22 to 14 AWG |
| Torque, hold-down screws | Not to exceed 1 in-lb (0.11 N-m) |
| Torque, connector screws | 5.22 in-lb (0.59 N-m) |
| Field Side Ratings (each channel) | |
| Nominal Input Voltage | 24 VAC/VDC |
| Channel-to-channel isolation | 300 VAC (1,500 V transient) |
| Input Voltage Range | 10–32 VAC/VDC |
| Turn-on Voltage | 10 VAC/VDC |
| Turn-off Voltage | 3 VAC/VDC |
| Input Resistance | 15 K ohms (nominal) |
| Logic Side Ratings | |
| Logic Output Voltage | <.5 V max. (on) @ 2 mA sinking, 2.7 V min. (off), @ 0.4 mA sourcing |
| Logic Supply Voltage*** | 5 VDC ± 0.25 VDC |
| Logic Supply Current | 50 mA maximum |
| Negative True Logic Output Drive | TTL 74 Series = 1 UL, TTL 74LS Series = 5 UL |
| Module Ratings | |
| Number of Channels Per Module | 4 |
| Turn-on Time | 5 msec |
| Turn-off Time | 15 msec |
| Optical Isolation (Field Side to Logic Side) | 4,000 volts (transient) |
| Temperature | -20 °C to 70 °C, operating |
| -40 °C to 85 °C, storage | |
| Agency Approvals | UL, CE, CSA, RoHS, DFARS, NEBS; UKCA |
| Warranty | Lifetime |
| * At 20kHz, 5Vp-p square wave input, 50% duty cycle. ** At 20kHz, 28Vp-p square wave input, 50% duty cycle. *** When used with an I/O processor (brain or on-the-rack controller), the processor requires 5.0 to 5.2 VDC. | |
SNAP-IDC5D
The SNAP-IDC5D provides four channels of 2.5-28 VDC digital input. Each channel senses the on/off status for DC voltages from sources such as proximity switches, push buttons, or auxiliary contacts. The module has removable top-mounted connectors for easy access to field wiring, as well as channel-specific LEDs for convenient troubleshooting.
SNAP 4-Ch 2.5-28 VDC Digital (Discrete) Input Module
SNAP-IDC5D
| Key Feature | -- |
| Wire size | 22 to 14 AWG |
| Torque, hold-down screws | Not to exceed 1 in-lb (0.11 N-m) |
| Torque, connector screws | 5.22 in-lb (0.59 N-m) |
| Field Side Ratings (each channel) | |
| Nominal Input Voltage | 5 VDC |
| Channel-to-channel isolation | 300 VAC (1,500 V transient) |
| Input Voltage Range | 2.5–28 VDC |
| Turn-on Voltage | 2.5 VDC |
| Turn-off Voltage | 1 VDC |
| Input Resistance | 3 K ohms (nominal) |
| Logic Side Ratings | |
| Logic Output Voltage | <.5 V max. (on) @ 2 mA sinking, 2.7 V min. (off), @ 0.4 mA sourcing |
| Logic Supply Voltage*** | 5 VDC ± 0.25 VDC |
| Logic Supply Current | 50 mA maximum |
| Negative True Logic Output Drive | TTL 74 Series = 1 UL, TTL 74LS Series = 5 UL |
| Module Ratings | |
| Number of Channels Per Module | 4 |
| Turn-on Time | 1 msec |
| Turn-off Time | 1 msec |
| Optical Isolation (Field Side to Logic Side) | 4,000 volts (transient) |
| Temperature | -20 °C to 70 °C, operating |
| -40 °C to 85 °C, storage | |
| Agency Approvals | UL, CE, CSA, RoHS, DFARS; UKCA |
| Warranty | Lifetime |
| * At 20kHz, 5Vp-p square wave input, 50% duty cycle. ** At 20kHz, 28Vp-p square wave input, 50% duty cycle. *** When used with an I/O processor (brain or on-the-rack controller), the processor requires 5.0 to 5.2 VDC. | |
SNAP-IDC5-FAST
The SNAP-IDC5-FAST provides four channels of high-speed 2.5-16 VDC digital input. Each channel senses the on/off status for DC voltages from sources such as proximity switches, push buttons, or auxiliary contacts. The module has removable top-mounted connectors for easy access to field wiring, as well as channel-specific LEDs for convenient troubleshooting.
SNAP 4-Ch High-Speed 2.5 - 16VDC Digital (Discrete) Input Module
SNAP-IDC5-FAST
| Key Feature | High-speed |
| Wire size | 22 to 14 AWG |
| Torque, hold-down screws | Not to exceed 1 in-lb (0.11 N-m) |
| Torque, connector screws | 5.22 in-lb (0.59 N-m) |
| Field Side Ratings (each channel) | |
| Nominal Input Voltage | 5 VDC |
| Channel-to-channel isolation | 300 VAC (1,500 V transient) |
| Input Voltage Range | 2.5–16 VDC |
| Turn-on Voltage | 2.5 VDC |
| Turn-off Voltage | 1 VDC |
| Input Resistance | 440 ohms (nominal) |
| Logic Side Ratings | |
| Logic Output Voltage | <0.5 V max. (on) @ 2 mA sinking 2.7 V min. (off) @ 0.4 mA sourcing |
| Logic Supply Voltage*** | 5 VDC ± 0.25 VDC |
| Logic Supply Current | 50 mA maximum |
| Negative True Logic Output Drive | TTL 74 Series = 1 UL TTL 74LS Series = 5 UL |
| Module Ratings | |
| Number of Channels Per Module | 4 |
| Turn-on Time | 0.025 msec* |
| Turn-off Time | 0.025 msec* |
| Optical Isolation (Field Side to Logic Side) | 4,000 volts (transient) |
| Temperature | -20 °C to 70 °C, operating |
| -40 °C to 85 °C, storage | |
| Agency Approvals | UL, CE, ATEX, CSA, RoHS, DFARS; UKCA |
| Warranty | Lifetime |
| * At 20kHz, 5Vp-p square wave input, 50% duty cycle. ** At 20kHz, 28Vp-p square wave input, 50% duty cycle. *** When used with an I/O processor (brain or on-the-rack controller), the processor requires 5.0 to 5.2 VDC. | |
SNAP-IDC5-FAST-A
The SNAP-IDC5-FAST-A provides four channels of high-speed 18-32 VDC digital input. Each channel senses the on/off status for DC voltages from sources such as proximity switches, push buttons, or auxiliary contacts. The module has removable top-mounted connectors for easy access to field wiring, as well as channel-specific LEDs for convenient troubleshooting.
SNAP 4-Ch High-Speed 18-32 VDC Digital (Discrete) Input Module
SNAP-IDC5-FAST-A
| Key Feature | High-speed |
| Wire size | 22 to 14 AWG |
| Torque, hold-down screws | Not to exceed 1 in-lb (0.11 N-m) |
| Torque, connector screws | 5.22 in-lb (0.59 N-m) |
| Field Side Ratings (each channel) | |
| Nominal Input Voltage | 28 VDC |
| Channel-to-channel isolation | 300 VAC (1,500 V transient) |
| Input Voltage Range | 18–32 VDC |
| Turn-on Voltage | 18 VDC |
| Turn-off Voltage | 5 VDC |
| Input Resistance | 8 K ohms (nominal) |
| Logic Side Ratings | |
| Logic Output Voltage | <0.5 V max. (on) @ 2 mA sinking 2.7 V min. (off) @ 0.4 mA sourcing |
| Logic Supply Voltage*** | 5 VDC ± 0.25 VDC |
| Logic Supply Current | 50 mA maximum |
| Negative True Logic Output Drive | TTL 74 Series = 1 UL TTL 74LS Series = 5 UL |
| Module Ratings | |
| Number of Channels Per Module | 4 |
| Turn-on Time | 0.025 msec* |
| Turn-off Time | 0.025 msec* |
| Optical Isolation (Field Side to Logic Side) | 4,000 volts (transient) |
| Temperature | -20 °C to 70 °C, operating |
| -40 °C to 85 °C, storage | |
| Agency Approvals | UL, CE, CSA, RoHS, DFARS; UKCA |
| Warranty | Lifetime |
| * At 20kHz, 5Vp-p square wave input, 50% duty cycle. ** At 20kHz, 28Vp-p square wave input, 50% duty cycle. *** When used with an I/O processor (brain or on-the-rack controller), the processor requires 5.0 to 5.2 VDC. | |
SNAP-IDC5MA
The SNAP-IDC5MA provides four channels of 10-32 VDC/VAC digital input. Each channel senses the on/off status for DC voltages from sources such as proximity switches, push buttons, or auxiliary contacts. This module features manual-on/manual-off/automatic switches that override input from field devices and are ideal for testing control applications.
SNAP 4-Ch Isolated 10-32 VDC/VAC Digital (Discrete) Input Module with Manual/Auto Switches
SNAP-IDC5MA
| Key Feature | High-speed |
| Wire size | 22 to 14 AWG |
| Torque, hold-down screws | Not to exceed 1 in-lb (0.11 N-m) |
| Torque, connector screws | 5.22 in-lb (0.59 N-m) |
| Field Side Ratings (each channel) | |
| Nominal Input Voltage | 24 VAC/VDC |
| Channel-to-channel isolation | 300 VAC (1,500 V transient) |
| Input Voltage Range | 10–32 VAC/VDC |
| Turn-on Voltage | 10 VAC/VDC |
| Turn-off Voltage | 3 VAC/VDC |
| Input Resistance | 15 K ohms (nominal) |
| Logic Side Ratings | |
| Logic Output Voltage | <0.5 V max. (on) @ 2 mA sinking 2.7 V min. (off) @ 0.4 mA sourcing |
| Logic Supply Voltage*** | 5 VDC ± 0.25 VDC |
| Logic Supply Current | 50 mA maximum |
| Negative True Logic Output Drive | TTL 74 Series = 1 UL TTL 74LS Series = 5 UL |
| Module Ratings | |
| Number of Channels Per Module | 4 |
| Turn-on Time | 5 msec |
| Turn-off Time | 15 msec |
| Optical Isolation (Field Side to Logic Side) | 4,000 volts (transient) |
| Temperature | -20 °C to 70 °C, operating |
| -40 °C to 85 °C, storage | |
| Agency Approvals | CE, RoHS, DFARS; UKCA |
| Warranty | 30 months |
| * At 20kHz, 5Vp-p square wave input, 50% duty cycle. ** At 20kHz, 28Vp-p square wave input, 50% duty cycle. *** When used with an I/O processor (brain or on-the-rack controller), the processor requires 5.0 to 5.2 VDC. | |
SNAP-IDC5-HT
The SNAP-IDC5-HT provides four channels of leakage-tolerant 15-32 VDC digital input. This module is designed for use with sensors that have a high leakage current. Removable top-mounted connectors on the module give easy access to field wiring, and channel-specific LEDs help in troubleshooting.
SNAP 4-Ch Leakage-Tolerant 15-32 VDC Digital Input Module
SNAP-IDC5-HT
| Key Feature | Leakage-tolerant |
| Wire size | 22 to 14 AWG |
| Torque, hold-down screws | Not to exceed 1 in-lb (0.11 N-m) |
| Torque, connector screws | 5.22 in-lb (0.59 N-m) |
| Field Side Ratings (each channel) | |
| Nominal Input Voltage | 24 VAC/VDC |
| Channel-to-channel isolation | 300 VAC (1,500 V transient) |
| Input Voltage Range | 15–32 VAC/VDC |
| Turn-on Voltage | 15 VAC/VDC |
| Turn-off Voltage | 8 VAC/VDC |
| Input Resistance | 3 K ohms (nominal) |
| Logic Side Ratings | |
| Logic Output Voltage | <0.5 V max. (on) @ 2 mA sinking 2.7 V min. (off) @ 0.4 mA sourcing |
| Logic Supply Voltage*** | 5 VDC ± 0.25 VDC |
| Logic Supply Current | 50 mA maximum |
| Negative True Logic Output Drive | TTL 74 Series = 1 UL TTL 74LS Series = 5 UL |
| Module Ratings | |
| Number of Channels Per Module | 4 |
| Turn-on Time | 20 msec |
| Turn-off Time | 25 msec |
| Optical Isolation (Field Side to Logic Side) | 4,000 volts (transient) |
| Temperature | -20 °C to 70 °C, operating |
| -40 °C to 85 °C, storage | |
| Agency Approvals | CE, RoHS, DFARS; UKCA |
| Warranty | Lifetime |
| * At 20kHz, 5Vp-p square wave input, 50% duty cycle. ** At 20kHz, 28Vp-p square wave input, 50% duty cycle. *** When used with an I/O processor (brain or on-the-rack controller), the processor requires 5.0 to 5.2 VDC. | |
SNAP-IDC-32
The SNAP-IDC-32 32-channel digital input module provides 32 digital input channels in one compact SNAP module. The SNAP-IDC-32 is ideal for OEMs and others who have applications with high point counts, or for those requiring large numbers of digital input channels on one SNAP I/O rack. The high-density configuration reduces per-point costs of digital I/O systems by providing up to eight times as many I/O channels in the same space.
SNAP 32-channel Digital (Discrete) Input Module, 10-32 VDC
SNAP-IDC-32
| Input Range | 10 to 32 VDC |
| Nominal Voltage Range | 24 VDC |
| Input Resistance | 20 K ohms |
| Logic Voltage and Current | 5 VDC ± 0.1 @ 150 mA |
| Maximum Operating Common Mode Voltage | 250 V |
| Isolation: Field to Logic | 1500 V |
| Input Arrangement | 32 input channels; 4 groups of 8 inputs each |
| Common connection | Points in each group share a common negative connection. |
| Channel-to-Channel Isolation | No channel-to-channel isolation; 100 V group-to-group isolation |
| Hold-down screws | Torque: Not to exceed 1 in-lb (0.11 N-m) |
| Connector screws | Torque: 5.22 in-lb (0.59 N-m) |
| Maximum Number of HDD Modules on One Mounting Rack | 16 |
| Indicators | None; use optional OptoTerminal-G20 diagnostic display or breakout rack. |
| ON Voltage | 10 VDC @ 0.5 mA |
| OFF Voltage | 3 VDC @ 0.1 mA |
| Polling time from I/O processor to module1 | 2–30 ms typical2 |
| Input Turn-On/Off Time | 6 ms |
| Counting Frequency (DC input) | 0–50 Hz @ 50% duty cycle |
| Operating Temperature | -20 to 70 °C |
| Storage Temperature | -40 to 85 °C |
| Agency Approvals | UL, CE, RoHS, DFARS; UKCA |
| Warranty | Lifetime |
| 1 Affects turn-on and turn-off determination 2 Time varies based on the SNAP PAC I/O processor (brain or on-the-rack controller), processor configuration, and Ethernet host communication activity. | |
SNAP-IDC-16
The SNAP-IDC-16 provides 16 isolated channels of 10-32 VDC input and features automatic counting and latching. It can be used to sense on/off status for 10–32 VDC inputs from sources such as proximity switches, limit switches, push buttons, and pilot switches.
SNAP Isolated 16-pt Digital (Discrete) Input Module, 10-32 VDC
SNAP-IDC-16
| Input Range | 10–32 VDC/VAC |
| Nominal Voltage Range | 24 VDC |
| Input Resistance | 44 K ohms |
| Logic Voltage and Current | 5 VDC ± 0.1 @ 150 mA |
| Input Arrangement | 16 isolated input channels |
| Channel-to-Channel Isolation | 250 V steady-state, 1500 V transient |
| Maximum Operating Common Mode Voltage | 250 V |
| Isolation: Field to Logic | 1500 V |
| Maximum Number of HDD Modules on One Mounting Rack | 16 |
| Indicators | None; use optional OptoTerminal-G20 diagnostic display. |
| ON Voltage | 10 VDC @ 0.230 mA |
| OFF Voltage | 3 VDC @ 0.05 mA |
| Torque, hold-down screws | Not to exceed 1 in-lb (0.11 N-m) |
| Torque, connector screws | 5.22 in-lb (0.59 N-m) |
| Polling time from I/O processor to module1 | 2–30 ms typical2 |
| Input Turn-On/Off Time | 15 ms turn-on time, 20 ms turn-off time |
| Counting Frequency (DC input) | 0–25 Hz @ 50% duty cycle |
| Operating Temperature | -20 to 70 °C |
| Storage Temperature | -40 to 85 °C |
| Agency Approvals | UL, CE, RoHS, DFARS; UKCA |
| Warranty | Lifetime |
| 1 Affects turn-on and turn-off determination 2 Time varies based on the SNAP PAC I/O processor (brain or on-the-rack controller), processor configuration, and Ethernet host communication activity. | |
SNAP-IDC-32N
The SNAP-IDC-32N 32-channel digital input module provides 32 digital input channels in one compact SNAP module. The SNAP-IDC-32N is ideal for OEMs and others who have applications with high point counts, or for those requiring large numbers of digital input channels on one SNAP I/O rack. The high-density configuration reduces per-point costs of digital I/O systems by providing up to eight times as many I/O channels in the same space.
SNAP 32-channel Digital (Discrete) Input Module, -10 to -32 VDC, with positive common connection
SNAP-IDC-32N
| Input Range | -10 to -32 VDC |
| Nominal Voltage Range | -12 to -24 VDC |
| Input Resistance | 20 K ohms |
| Logic Voltage and Current | 5 VDC ± 0.1 @ 150 mA |
| Maximum Operating Common Mode Voltage | 250 V |
| Isolation: Field to Logic | 1500 V |
| Input Arrangement | 32 input channels; 4 groups of 8 inputs each |
| Common connection | Points in each group share a common positive connection. |
| Channel-to-Channel Isolation | No channel-to-channel isolation; 100 V group-to-group isolation |
| Hold-down screws | Torque: Not to exceed 1 in-lb (0.11 N-m) |
| Connector screws | Torque: 5.22 in-lb (0.59 N-m) |
| Maximum Number of HDD Modules on One Mounting Rack | 16 |
| Indicators | None; use optional OptoTerminal-G20 diagnostic display or breakout rack. |
| ON Voltage | -10 VDC @ 0.5 mA |
| OFF Voltage | -3 VDC @ 0.1 mA |
| Polling time from I/O processor to module1 | 2–30 ms typical2 |
| Input Turn-On/Off Time | 6 ms |
| Counting Frequency (DC input) | 0–50 Hz @ 50% duty cycle |
| Operating Temperature | -20 to 70 °C |
| Storage Temperature | -40 to 85 °C |
| Agency Approvals | CE, RoHS, DFARS |
| Warranty | Lifetime |
| 1 Affects turn-on and turn-off determination 2 Time varies based on the SNAP PAC I/O processor (brain or on-the-rack controller), processor configuration, and Ethernet host communication activity. | |
SNAP-IDC-HT-16
The SNAP-IDC-HT-16 leakage tolerant digital input module is used with proximity switches. It offers channel-to-channel isolation for 16 points and senses on/off status for loads of 15–28 VDC/VAC. The SNAP-IDC-HT-16 features automatic counting and latching.
SNAP isolated 16-pt digital (discrete) input module, leakage tolerant, 15-28 VDC
SNAP-IDC-HT-16
| Input Range | 15–28 VDC/VAC |
| Nominal Voltage Range | 24 VDC |
| Input Resistance | 4 K ohms |
| Logic Voltage and Current | 5 VDC ± 0.1 @ 150 mA |
| Input Arrangement | 16 isolated input channels |
| Channel-to-Channel Isolation | 250 V steady-state, 1500 V transient |
| Maximum Operating Common Mode Voltage | 250 V |
| Isolation: Field to Logic | 1500 V |
| Maximum Number of HDD Modules on One Mounting Rack | 16 |
| Indicators | None; use optional OptoTerminal-G20 diagnostic display. |
| ON Voltage | 15 VDC @ 3.50 mA |
| OFF Voltage | 9 VDC @ 2.0 mA |
| Torque, hold-down screws | Not to exceed 1 in-lb (0.11 N-m) |
| Torque, connector screws | 5.22 in-lb (0.59 N-m) |
| Polling time from I/O processor to module1 | 2–30 ms typical2 |
| Input Turn-On/Off Time | 20 ms turn-on time, 25 ms turn-off time |
| Counting Frequency (DC input) | 0–15 Hz @ 50% duty cycle |
| Operating Temperature | -20 to 70 °C |
| Storage Temperature | -40 to 85 °C |
| Agency Approvals | CE, RoHS, DFARS |
| Warranty | Lifetime |
| 1 Affects turn-on and turn-off determination 2 Time varies based on the SNAP PAC I/O processor (brain or on-the-rack controller), processor configuration, and Ethernet host communication activity. | |
SNAP-IDC-32DN
The SNAP-IDC-32DN 32-channel digital input module provides 32 digital input channels in one compact SNAP module. The SNAP-IDC-32DN is ideal for OEMs and others who have applications with high point counts, or for those requiring large numbers of digital input channels on one SNAP I/O rack. The high-density configuration reduces per-point costs of digital I/O systems by providing up to eight times as many I/O channels in the same space.
SNAP 32-channel Digital (Discrete) Input Module, -2.5 to -12 VDC, with positive common connection
SNAP-IDC-32DN
| Input Range | -2.5 to -12 VDC |
| Nominal Voltage Range | -2.5 VDC |
| Input Resistance | 3 K ohms |
| Logic Voltage and Current | 5 VDC ± 0.1 @ 150 mA |
| Maximum Operating Common Mode Voltage | 250 V |
| Isolation: Field to Logic | 1500 V |
| Input Arrangement | 32 input channels; 4 groups of 8 inputs each |
| Common connection | Points in each group share a common positive connection. |
| Channel-to-Channel Isolation | No channel-to-channel isolation; 100 V group-to-group isolation |
| Hold-down screws | Torque: Not to exceed 1 in-lb (0.11 N-m) |
| Connector screws | Torque: 5.22 in-lb (0.59 N-m) |
| Maximum Number of HDD Modules on One Mounting Rack | 16 |
| Indicators | None; use optional OptoTerminal-G20 diagnostic display or breakout rack. |
| ON Voltage | -2.5 VDC @ 0.5 mA |
| OFF Voltage | -1 VDC @ 0.1 mA |
| Polling time from I/O processor to module1 | 2–30 ms typical2 |
| Input Turn-On/Off Time | 6 ms |
| Counting Frequency (DC input) | 0–50 Hz @ 50% duty cycle |
| Operating Temperature | -20 to 70 °C |
| Storage Temperature | -40 to 85 °C |
| Agency Approvals | CE, RoHS, DFARS |
| Warranty | Lifetime |
| 1 Affects turn-on and turn-off determination 2 Time varies based on the SNAP PAC I/O processor (brain or on-the-rack controller), processor configuration, and Ethernet host communication activity. | |
SNAP-IDC-32D
The SNAP-IDC-32D digital input module, with 32 input points, can be used to sense on/off status for 2.5 to 12 VDC inputs from sources such as proximity switches, limit switches, push buttons, and pilot switches (PNP or sourcing type).
SNAP 32-channel Digital (Discrete) Input Module, 2.5 to 12 VDC
SNAP-IDC-32D
| Input Range | 2.5 to 12 VDC |
| Nominal Voltage Range | 2.5 VDC |
| Input Resistance | 3 K ohms |
| Logic Voltage and Current | 5 VDC ± 0.1 @ 150 mA |
| Maximum Operating Common Mode Voltage | 250 V |
| Isolation: Field to Logic | 1500 V |
| Input Arrangement | 32 input channels; 4 groups of 8 inputs each |
| Common connection | Points in each group share a common negative connection. |
| Channel-to-Channel Isolation | No channel-to-channel isolation; 100 V group-to-group isolation |
| Hold-down screws | Torque: Not to exceed 1 in-lb (0.11 N-m) |
| Connector screws | Torque: 5.22 in-lb (0.59 N-m) |
| Maximum Number of HDD Modules on One Mounting Rack | 16 |
| Indicators | None; use optional OptoTerminal-G20 diagnostic display or breakout rack. |
| ON Voltage | 2.5 VDC @ 0.5 mA |
| OFF Voltage | 1 VDC @ 0.1 mA |
| Polling time from I/O processor to module1 | 2–30 ms typical2 |
| Input Turn-On/Off Time | 6 ms |
| Counting Frequency (DC input) | 0–50 Hz @ 50% duty cycle |
| Operating Temperature | -20 to 70 °C |
| Storage Temperature | -40 to 85 °C |
| Agency Approvals | CE, RoHS, DFARS |
| Warranty | Lifetime |
| 1 Affects turn-on and turn-off determination 2 Time varies based on the SNAP PAC I/O processor (brain or on-the-rack controller), processor configuration, and Ethernet host communication activity. | |
DC Output SNAP Digital I/O Modules
SNAP-ODC5SRC
The SNAP-ODC5SRC provides four channels of 5-60 VDC digital output in a source configuration, each channel switching a separate DC load. The module features a removable top-mounted connector for easy access to field wiring and channel-specific LEDs for troubleshooting.
SNAP 4-Ch 5-60 VDC Digital (Discrete) Output Module, Load Sourcing
SNAP-ODC5SRC
| Key Feature | Load sourcing |
| Torque, hold-down screws | Not to exceed 1 in-lb (0.11 N-m) |
| Torque, connector screws | 5.22 in-lb (0.59 N-m) |
| Field Side Ratings (each channel) | |
| Line Voltage - Range | 5–60 VDC |
| Line Voltage - Nominal | 5–48 VDC |
| Current Rating 0 °C to 70 °C Ambient | 3 amps per module |
| Surge Current | 5 amps peak for 1 second |
| Minimum Load | 20 mA |
| Output Voltage Drop | 1.6 volts max.@ 0.75 amps |
| Off-state Leakage | 1 mA @ 60 VDC |
| Peak Blocking Voltage | 60 VDC |
| Fuse (Common to all Channels) | 250 VAC - 4A 5x20 mm Fast-acting Bell Fuse Part No. BEL 5HF4 Opto 22 Part SNAP-FUSE4AB |
| Channel-to-channel isolation | Not applicable |
| Logic Side Ratings | |
| Pickup Voltage | 4 V @ 5.5 mA |
| Dropout Voltage | 1 VDC |
| Control Resistance | 220 ohms |
| Logic Supply Voltage | 5 VDC ± 0.25 VDC |
| Logic Supply Current | 50 mA maximum |
| Module Ratings | |
| Number of Channels Per Module | 4 |
| Turn-on Time | 100 usec |
| Turn-off Time | 750 usec |
| Isolation (Field Side to Logic Side) | 4,000 volts (transient) |
| Operating Temperature | -20 to 70 °C |
| Storage Temperature | -40 to 85 °C |
| Wire size range | 22 to 14 AWG |
| Agency Approvals | UL, CE, CSA, RoHS, DFARS; UKCA |
| Warranty | Lifetime |
SNAP-ODC5SNK
The SNAP-ODC5SNK provides four channels of 5-60 VDC digital output in a sink configuration, each channel switching a separate DC load. The module features a removable top-mounted connector for easy access to field wiring and channel-specific LEDs for troubleshooting.
SNAP 4-Ch 5-60 VDC Digital (Discrete) Output Module, Load Sinking
SNAP-ODC5SNK
| Key Feature | Load sinking |
| Torque, hold-down screws | Not to exceed 1 in-lb (0.11 N-m) |
| Torque, connector screws | 5.22 in-lb (0.59 N-m) |
| Field Side Ratings (each channel) | |
| Line Voltage - Range | 5–60 VDC |
| Line Voltage - Nominal | 5–48 VDC |
| Current Rating 0 °C to 70 °C Ambient | 3 amps per module |
| Surge Current | 5 amps peak for 1 second |
| Minimum Load | 20 mA |
| Output Voltage Drop | 1.6 volts max.@ 0.75 amps |
| Off-state Leakage | 1 mA @ 60 VDC |
| Peak Blocking Voltage | 60 VDC |
| Fuse (Common to all Channels) | 250 VAC - 4A 5x20 mm Fast-acting Bell Fuse Part No. BEL 5HF4 Opto 22 Part SNAP-FUSE4AB |
| Channel-to-channel isolation | Not applicable |
| Logic Side Ratings | |
| Pickup Voltage | 4 V @ 5.5 mA |
| Dropout Voltage | 1 VDC |
| Control Resistance | 220 ohms |
| Logic Supply Voltage | 5 VDC ± 0.25 VDC |
| Logic Supply Current | 50 mA maximum |
| Module Ratings | |
| Number of Channels Per Module | 4 |
| Turn-on Time | 100 usec |
| Turn-off Time | 750 usec |
| Isolation (Field Side to Logic Side) | 4,000 volts (transient) |
| Operating Temperature | -20 to 70 °C |
| Storage Temperature | -40 to 85 °C |
| Wire size range | 22 to 14 AWG |
| Agency Approvals | UL, CE, CSA, RoHS, DFARS; UKCA |
| Warranty | Lifetime |
SNAP-ODC5MA
The SNAP-ODC5MA provides four isolated channels of 5-60 VDC digital output, each switching a separate DC load. The module features manual-on/manual-off/automatic switches that override output from the application and are ideal for testing field device wiring.
SNAP 4-Ch Isolated 5-60 VDC Digital (Discrete) Output Module with Manual/Auto Switches
SNAP-ODC5MA
| Key Feature | Diagnostic switches Four isolated channels |
| Torque, hold-down screws | Not to exceed 1 in-lb (0.11 N-m) |
| Torque, connector screws | 5.22 in-lb (0.59 N-m) |
| Field Side Ratings (each channel) | |
| Line Voltage - Range | 5–60 VDC |
| Line Voltage - Nominal | 5–48 VDC |
| Current Rating 0 °C to 70 °C Ambient | 2 amps per module 0.5 amps per channel |
| Surge Current | 5 amps peak for 1 second |
| Minimum Load | 20 mA |
| Output Voltage Drop | 1.6 volts max.@ 0.75 amps |
| Off-state Leakage | 1 mA @ 60 VDC |
| Peak Blocking Voltage | 60 VDC |
| Fuse (Common to all Channels) | Has four isolated channels. User must provide own fusing. |
| Channel-to-channel isolation | 300 VAC (1500 V transient) |
| Logic Side Ratings | |
| Pickup Voltage | 4 V @ 5.5 mA |
| Dropout Voltage | 1 VDC |
| Control Resistance | 220 ohms |
| Logic Supply Voltage | 5 VDC ± 0.25 VDC |
| Logic Supply Current | 50 mA maximum |
| Module Ratings | |
| Number of Channels Per Module | 4 |
| Turn-on Time | 100 usec |
| Turn-off Time | 750 usec |
| Isolation (Field Side to Logic Side) | 4,000 volts (transient) |
| Operating Temperature | -20 ° to 70 °C |
| Storage Temperature | -40 ° to 85 °C |
| Wire size range | 22 to 14 AWG |
| Agency Approvals | UL, CE, RoHS, DFARS; UKCA |
| Warranty | 30 months |
SNAP-ODC5-i
The SNAP-ODC5-i provides four isolated channels of 5-60 VDC digital output, each switching a separate DC load. The module features channel-specific LEDs for troubleshooting and includes a connector clamp to prevent sparks.
SNAP 4-Ch Isolated 5-60 VDC Digital (Discrete) Output Module
SNAP-ODC5-i
| Key Feature | Four isolated channels |
| Torque, hold-down screws | Not to exceed 1 in-lb (0.11 N-m) |
| Torque, connector screws | 5.22 in-lb (0.59 N-m) |
| Field Side Ratings (each channel) | |
| Line Voltage - Range | 5–60 VDC |
| Line Voltage - Nominal | 5–48 VDC |
| Current Rating 0 °C to 70 °C Ambient | 3 amps per module |
| Surge Current | 5 amps peak for 1 second |
| Minimum Load | 20 mA |
| Output Voltage Drop | 1.6 volts max.@ 0.75 amps |
| Off-state Leakage | 1 mA @ 60 VDC |
| Peak Blocking Voltage | 60 VDC |
| Fuse (Common to all Channels) | Has four isolated channels. User must provide own fusing. |
| Channel-to-channel isolation | 300 VAC (1500 V transient) |
| Logic Side Ratings | |
| Pickup Voltage | 4 V @ 5.5 mA |
| Dropout Voltage | 1 VDC |
| Control Resistance | 220 ohms |
| Logic Supply Voltage | 5 VDC ± 0.25 VDC |
| Logic Supply Current | 50 mA maximum |
| Module Ratings | |
| Number of Channels Per Module | 4 |
| Turn-on Time | 100 usec |
| Turn-off Time | 750 usec |
| Isolation (Field Side to Logic Side) | 4,000 volts (transient) |
| Operating Temperature | -20 ° to 70 °C |
| Storage Temperature | -40 ° to 85 °C |
| Wire size range | 22 to 14 AWG |
| Agency Approvals | UL, CE, RoHS, DFARS; UKCA |
| Warranty | Lifetime |
SNAP-ODC5A-i
The SNAP-ODC5A-i provides four isolated channels of 5-200 VDC digital output, each switching a separate DC load. The module features channel-specific LEDs for troubleshooting and includes a connector clamp to prevent sparks.
SNAP 4-Ch Isolated 5-200 VDC Digital (Discrete) Output Module
SNAP-ODC5A-i
| Key Feature | Four isolated channels |
| Torque, hold-down screws | Not to exceed 1 in-lb (0.11 N-m) |
| Torque, connector screws | 5.22 in-lb (0.59 N-m) |
| Field Side Ratings (each channel) | |
| Line Voltage - Range | 5–200 VDC |
| Line Voltage - Nominal | 5–200 VDC |
| Current Rating 0 °C to 70 °C Ambient | 3 amps per module |
| Surge Current | 5 amps peak for 1 second |
| Minimum Load | 20 mA |
| Output Voltage Drop | 1.6 volts max.@ 0.75 amps |
| Off-state Leakage | 1 mA @ 60 VDC |
| Peak Blocking Voltage | 200 VDC |
| Fuse (Common to all Channels) | Has four isolated channels. User must provide own fusing. |
| Channel-to-channel isolation | 300 VAC (1500 V transient) |
| Logic Side Ratings | |
| Pickup Voltage | 4 V @ 5.5 mA |
| Dropout Voltage | 1 VDC |
| Control Resistance | 220 ohms |
| Logic Supply Voltage | 5 VDC ± 0.25 VDC |
| Logic Supply Current | 50 mA maximum |
| Module Ratings | |
| Number of Channels Per Module | 4 |
| Turn-on Time | 100 usec |
| Turn-off Time | 750 usec |
| Isolation (Field Side to Logic Side) | 4,000 volts (transient) |
| Operating Temperature | -20 ° to 70 °C |
| Storage Temperature | -40 ° to 85 °C |
| Wire size range | 22 to 14 AWG |
| Agency Approvals | UL, CE, RoHS, DFARS; UKCA |
| Warranty | Lifetime |
SNAP-ODC5ASNK
The SNAP-ODC5ASNK provides four channels of 5-200 VDC digital output in a sink configuration, each channel switching a separate DC load. The module features a removable top-mounted connector for easy access to field wiring and channel-specific LEDs for troubleshooting.
SNAP 4-Ch 5-200 VDC Digital (Discrete) Output Module, Load Sinking
SNAP-ODC5ASNK
| Key Feature | Load sinking |
| Torque, hold-down screws | Not to exceed 1 in-lb (0.11 N-m) |
| Torque, connector screws | 5.22 in-lb (0.59 N-m) |
| Field Side Ratings (each channel) | |
| Line Voltage - Range | 5–200 VDC |
| Line Voltage - Nominal | 5–200 VDC |
| Current Rating 0 °C to 70 °C Ambient | 3 amps per module |
| Surge Current | 5 amps peak for 1 second |
| Minimum Load | 20 mA |
| Output Voltage Drop | 1.6 volts max.@ 0.75 amps |
| Off-state Leakage | 1 mA @ 200 VDC |
| Peak Blocking Voltage | 200 VDC |
| Fuse (Common to all Channels) | 250 VAC - 4A 5x20 mm Fast-acting Bell Fuse Part: BEL 5HF4 Opto 22 Part: SNAP-FUSE4AB |
| Channel-to-channel isolation | Not applicable |
| Logic Side Ratings | |
| Pickup Voltage | 4 V @ 5.5 mA |
| Dropout Voltage | 1 VDC |
| Control Resistance | 220 ohms |
| Logic Supply Voltage | 5 VDC ± 0.25 VDC |
| Logic Supply Current | 50 mA maximum |
| Module Ratings | |
| Number of Channels Per Module | 4 |
| Turn-on Time | 100 usec |
| Turn-off Time | 750 usec |
| Isolation (Field Side to Logic Side) | 4,000 volts (transient) |
| Operating Temperature | -20 ° to 70 °C |
| Storage Temperature | -40 ° to 85 °C |
| Wire size range | 22 to 14 AWG |
| Agency Approvals | UL, CE, RoHS, DFARS; UKCA |
| Warranty | Lifetime |
SNAP-ODC-32-SRC
The SNAP-ODC-32-SRC digital output module (load sourcing) provides 32 digital output channels in one compact SNAP module. This module is ideal for OEMs and others with applications with high point counts, or for those requiring a large number of digital output channels on one SNAP I/O rack. The high-density configuration reduces per-point costs of digital I/O systems by providing up to eight times as many I/O channels in the same space.
SNAP 32-channel Digital (Discrete) Output Module, 5-60 VDC Load Sourcing
SNAP-ODC-32-SRC
| Switching Voltage | 5–60 VDC |
| Nominal Switching Voltage | 12–24 VDC |
| Logic Voltage and Current | 5 VDC ± 0.1 @ 150 mA |
| Maximum Off State Voltage | 60 VDC |
| Output Leakage, Typical | <10 microamps per channel (60 V, 70 °C) |
| Maximum Load per Point | 0.25 A |
| Voltage Drop | 0.15 VDC @ 0.25 A |
| Surge (1 sec.) | 1 A |
| Output Arrangement | 32 output channels; 4 groups of 8 outputs each. Points in each group share a common negative connection. |
| Maximum Operating Common Mode Voltage | 250 V |
| Isolation: Field to Logic | 1500 V |
| Output Turn-On/Off Time | 100 microseconds |
| Polling time from I/O processor to module1 | 2–30 ms typical2 |
| Indicators | None; use optional OptoTerminal-G20 diagnostic display or breakout rack. |
| Maximum Number of HDD Modules on One Mounting Rack | 16 |
| Torque, hold-down screws | Not to exceed 1 in-lb (0.11 N-m) |
| Torque, connector screws | 5.22 in-lb (0.59 N-m) |
| Operating Temperature | -20 to 70 °C |
| Storage Temperature | -40 to 85 °C |
| Agency Approvals | SNAP-ODC-32-SRC: UL, CE, RoHS, DFARS; UKCA SNAP-ODC-32-SRC-FM: CE, FM, RoHS, DFARS; UKCA |
| Warranty | Lifetime |
| 1 Affects turn-on and turn-off determination 2 Time varies based on the SNAP PAC I/O processor (brain or on-the-rack controller), processor configuration, and Ethernet host communication activity. | |
SNAP-ODC-32-SNK
The SNAP-ODC-32-SNK digital output module (load sinking) provides 32 digital output channels in one compact SNAP module. This module is ideal for OEMs and others with applications with high point counts, or for those requiring a large number of digital output channels on one SNAP I/O rack. The high-density configuration reduces per-point costs of digital I/O systems by providing up to eight times as many I/O channels in the same space.
SNAP 32-channel Digital (Discrete) Output Module, 5-60 VDC Load Sinking
SNAP-ODC-32-SNK
| Switching Voltage | 5–60 VDC |
| Nominal Switching Voltage | 12–24 VDC |
| Logic Voltage and Current | 5 VDC ± 0.1 @ 150 mA |
| Maximum Off State Voltage | 60 VDC |
| Output Leakage, Typical | <10 microamps per channel (60 V, 70 °C) |
| Maximum Load per Point | 0.25 A |
| Voltage Drop | 0.15 VDC @ 0.25 A |
| Surge (1 sec.) | 1 A |
| Output Arrangement | 32 output channels; 4 groups of 8 outputs each. Points in each group share a common negative connection. |
| Maximum Operating Common Mode Voltage | 250 V |
| Isolation: Field to Logic | 1500 V |
| Output Turn-On/Off Time | 100 microseconds |
| Polling time from I/O processor to module1 | 2–30 ms typical2 |
| Indicators | None; use optional OptoTerminal-G20 diagnostic display or breakout rack. |
| Maximum Number of HDD Modules on One Mounting Rack | 16 |
| Torque, hold-down screws | Not to exceed 1 in-lb (0.11 N-m) |
| Torque, connector screws | 5.22 in-lb (0.59 N-m) |
| Operating Temperature | -20 to 70 °C |
| Storage Temperature | -40 to 85 °C |
| Agency Approvals | CE, RoHS, DFARS; UKCA |
| Warranty | Lifetime |
| 1 Affects turn-on and turn-off determination 2 Time varies based on the SNAP PAC I/O processor (brain or on-the-rack controller), processor configuration, and Ethernet host communication activity. | |
Dry Contact SNAP Digital I/O Modules
SNAP-ODC5R
The SNAP-ODC5R is a digital output module that uses low-voltage mechanical relays and does not provide optical isolation. Current rating depends on the voltage the module is used with. This module is normally open.
SNAP 4-Ch Low-voltage Mechanical Relay Digital (Discrete) Output Module, Normally Open
SNAP-ODC5R
| Key Feature | Dry contact Normally open |
| Torque, hold-down screws | Not to exceed 1 in-lb (0.11 N-m) |
| Torque, connector screws | 5.22 in-lb (0.59 N-m) |
| Field Side Ratings (each channel) | |
| Line Voltage - Range | 0–100 VDC, 0–130 VAC* |
| Line Voltage - Nominal | -- |
| Current Rating | 0.5 amps switching* |
| Surge Current | 0.5 amps* |
| Minimum Load | 0 mA |
| Output Voltage Drop | 0 volts |
| Off-state Leakage | 0 mA |
| Peak Blocking Voltage | 100 VDC / 130 VAC |
| Fuse (Common to all Channels) | Has four isolated channels. User must provide own fusing. |
| Channel-to-channel isolation | 300 VAC (1500 V transient) |
| Logic Side Ratings | |
| Pickup Voltage | 4 V @ 5.5 mA |
| Dropout Voltage | 1 VDC |
| Control Resistance | 220 ohms |
| Logic Supply Voltage | 5 VDC ± 0.25 VDC |
| Logic Supply Current | 50 mA maximum |
| Module Ratings | |
| Number of Channels Per Module | 4 |
| Turn-on Time | 500 usec |
| Turn-off Time | 500 usec |
| Isolation (Field Side to Logic Side) | 1,500 volts (transient) |
| Mechanical Life | 200,000,000 cycles |
| Operating Temperature | -20 to 70 °C |
| Storage Temperature | -30 to 85 °C |
| Agency Approvals | CE, CSA, RoHS, DFARS; UKCA |
| Warranty | 30 months or mechanical life, whichever comes first |
| * The current of the dry contact module must not exceed 10 VA power limit under steady state or momentary in-rush conditions. For voltages at or below 20 volts, the current limit is 0.5 amps. For voltages above 20 volts, the maximum allowable current is determined by the following equation: Current Maximum = 10 VA / Voltage. Rating curve is in the data sheet. | |
SNAP-ODC5R5
The SNAP-ODC5R5 is a digital output module that uses low-voltage mechanical relays and does not provide optical isolation. Current rating depends on the voltage the module is used with. This module is normally closed.
SNAP 4-Ch Low-voltage Mechanical Relay Digital (Discrete) Output Module, Normally Closed
SNAP-ODC5R5
| Key Feature | Dry contact Normally closed |
| Torque, hold-down screws | Not to exceed 1 in-lb (0.11 N-m) |
| Torque, connector screws | 5.22 in-lb (0.59 N-m) |
| Field Side Ratings (each channel) | |
| Line Voltage - Range | 0–100 VDC, 0–130 VAC* |
| Line Voltage - Nominal | -- |
| Current Rating | 0.5 amps switching* |
| Surge Current | 0.5 amps* |
| Minimum Load | 0 mA |
| Output Voltage Drop | 0 volts |
| Off-state Leakage | 0 mA |
| Peak Blocking Voltage | 100 VDC / 130 VAC |
| Fuse (Common to all Channels) | Has four isolated channels. User must provide own fusing. |
| Channel-to-channel isolation | 300 VAC (1500 V transient) |
| Logic Side Ratings | |
| Pickup Voltage | 4 V @ 5.5 mA |
| Dropout Voltage | 1 VDC |
| Control Resistance | 220 ohms |
| Logic Supply Voltage | 5 VDC ± 0.25 VDC |
| Logic Supply Current | 50 mA maximum |
| Module Ratings | |
| Number of Channels Per Module | 4 |
| Turn-on Time | 500 usec |
| Turn-off Time | 500 usec |
| Isolation (Field Side to Logic Side) | 1,500 volts (transient) |
| Mechanical Life | 200,000,000 cycles |
| Operating Temperature | -20 to 70 °C |
| Storage Temperature | -30 to 85 °C |
| Agency Approvals | CE, RoHS, DFARS; UKCA |
| Warranty | 30 months or mechanical life, whichever comes first |
| * The current of the dry contact module must not exceed 10 VA power limit under steady state or momentary in-rush conditions. For voltages at or below 20 volts, the current limit is 0.5 amps. For voltages above 20 volts, the maximum allowable current is determined by the following equation: Current Maximum = 10 VA / Voltage. Rating curve is in the data sheet. | |
SNAP-IDC5-SW
The SNAP-IDC5-SW module provides four channels of contact status input. The module supplies 15 volts of power to an external dry contact switch and senses switch closure. Each user-supplied switch is connected with two wires. Because the module includes power for the switch, it is particularly cost-effective when labor costs for wiring external power are high.
SNAP 4-Ch Contact Status Input Module, Normally Open
SNAP-IDC5-SW
| Field Side Ratings (each channel) | |
| Open Circuit Voltage (Switch Open) | 15 VDC typical |
| Short Circuit Current (Switch Closed) | 7 milliamps nominal |
| Minimum Off Resistance | >20 K ohms |
| Maximum Allowable On Resistance (Wire + Contact Resistance) | 500 ohms |
| Logic Side Ratings | |
| Logic Output Voltage for SNAP-IDC5-SW (normally open) | <0.5 V max. (switch closed; LED on), @ 2 mA sinking, 2.7 V min. (switch open; LED off), @ 0.4 mA sourcing |
| Logic Output Voltage for SNAP-IDC5-SW-NC (normally closed) | <0.5 V max.(switch closed; LED off), @ 2 mA sinking, 2.7 V min. (switch open; LED on), @ 0.4 mA sourcing |
| Maximum Operating Common Mode Voltage (Field Term to Logic Connector) | 250 V |
| Power Requirements | 5 VDC (±0.25) @ 200 mA |
| Module Ratings | |
| Number of Channels Per Module | 4 |
| Turn-on Time | 5 msec |
| Turn-off Time | 25 msec |
| Channel-to-channel Isolation | None |
| Input-to-output Isolation | 1500 V AC/DC |
| Wire size | 22 to 14 AWG |
| Torque, hold-down screws | Not to exceed 1 in-lb (0.11 N-m) |
| Torque, connector screws | 5.22 in-lb (0.59 N-m) |
| Operating Temperature | -20 °C to 70 °C |
| Storage Temperature | -40 °C to 85 °C |
| Agency Approvals | UL, CE, RoHS, DFARS; UKCA |
| Warranty | Lifetime |
SNAP-IDC5-SW-NC
The SNAP-IDC5-SW-NC module provides four channels of contact status input. The module supplies 15 volts of power to an external dry contact switch and senses when the switch opens. Each user-supplied switch is connected with two wires. Because the module includes power for the switch, it is particularly cost-effective when labor costs for wiring external power are high.
SNAP 4-Ch Contact Status Input Module, Normally Closed
SNAP-IDC5-SW-NC
| Field Side Ratings (each channel) | |
| Open Circuit Voltage (Switch Open) | 15 VDC typical |
| Short Circuit Current (Switch Closed) | 7 milliamps nominal |
| Minimum Off Resistance | >20 K ohms |
| Maximum Allowable On Resistance (Wire + Contact Resistance) | 500 ohms |
| Logic Side Ratings | |
| Logic Output Voltage for SNAP-IDC5-SW (normally open) | <0.5 V max. (switch closed; LED on), @ 2 mA sinking, 2.7 V min. (switch open; LED off), @ 0.4 mA sourcing |
| Logic Output Voltage for SNAP-IDC5-SW-NC (normally closed) | <0.5 V max.(switch closed; LED off), @ 2 mA sinking, 2.7 V min. (switch open; LED on), @ 0.4 mA sourcing |
| Maximum Operating Common Mode Voltage (Field Term to Logic Connector) | 250 V |
| Power Requirements | 5 VDC (±0.25) @ 200 mA |
| Module Ratings | |
| Number of Channels Per Module | 4 |
| Turn-on Time | 5 msec |
| Turn-off Time | 25 msec |
| Channel-to-channel Isolation | None |
| Input-to-output Isolation | 1500 V AC/DC |
| Wire size | 22 to 14 AWG |
| Torque, hold-down screws | 22 to 14 AWG |
| Torque, hold-down screws | Not to exceed 1 in-lb (0.11 N-m) |
| Torque, connector screws | 5.22 in-lb (0.59 N-m) |
| Operating Temperature | -20 °C to 70 °C |
| Storage Temperature | -40 °C to 85 °C |
| Agency Approvals | UL, CE, RoHS, DFARS; UKCA FM (SNAP-IDC5SW only) |
| Warranty | Lifetime |
SNAP-OMR6-C
The UL-approved SNAP-OMR6-C mechanical power relay output module offers four channels of switching for up to 250 VAC or 30 VDC, 6 amp loads. Each of the four mechanical contacts can be used as normally open or normally closed.
SNAP Isolated 4-channel Mechanical Power Relay Output Module, Form C
SNAP-OMR6-C
| Field Side Ratings (each channel) | |
| Contact Configuration | Form C (SPDT, normally open or closed) |
| Line Voltage - Range | 0–250 VAC or 5–30 VDC |
| Current Rating | 6 amps switching @ 250 VAC / 30 VDC |
| Surge Current | 6 amps |
| Minimum Load | 5 VDC, 10 mA |
| Contact Resistance | ≤ 100 milliohms |
| Leakage Current | none |
| Clamping Voltage (for transient suppression) | External transient suppression required |
| Duty Cycle | -- Not applicable -- |
| Switching Power | 1500 VA / 144 W (DC) |
| Peak Blocking Voltage | 250 VAC @ 360 Vpk |
| Channel-to-channel isolation | 300 VAC (1500 V transient) |
| Logic Side Ratings | |
| Pickup Voltage | 1 V @ 2 mA |
| Dropout Voltage | 4 VDC |
| Control Resistance | 220 ohms |
| Logic Supply Voltage | 5 VDC ± 0.25 VDC |
| Logic Supply Current | 160 mA maximum |
| Module Ratings | |
| Number of Channels Per Module | 4 |
| Turn-on Time | 8 milliseconds |
| Turn-off Time | 8 milliseconds |
| Torque, hold-down screws | Not to exceed 1 in-lb (0.11 N-m) |
| Torque, connector screws | Single gray connector: 5.22 in-lb (0.59 N-m) Black connectors: 1.7 in-lb (0.2 N-m) |
| Operation Temperature | -20 to 70 °C |
| Storage Temperature | -30 to 85 °C |
| Agency Approvals | UL, CE, RoHS, DFARS; UKCA |
| Mechanical Life | 10 x 106 operations |
| Operational Life | 30 x 103 operations |
| Warranty | 30 months |
SNAP-OMR6T-C
The SNAP-OMR6T-C mechanical power relay output module offers four channels of switching for up to 250 VAC or 30 VDC, 6 amp loads. Each of the four mechanical contacts can be used as normally open or normally closed. This module includes integrated transient suppression while maintaining minimal leakage current.
SNAP Isolated 4-channel Mechanical Power Relay Output Module, Form C, with Integrated Transient Suppression
SNAP-OMR6T-C
| Field Side Ratings (each channel) | |
| Contact Configuration | Form C (SPDT, normally open or closed) |
| Line Voltage - Range | 0–250 VAC or 5–30 VDC |
| Current Rating | 6 amps switching @ 250 VAC / 30 VDC |
| Surge Current | 6 amps |
| Minimum Load | 5 VDC, 10 mA |
| Contact Resistance | ≤ 100 milliohms |
| Leakage Current | < 1 microamp @ 250 VAC |
| Clamping Voltage (for transient suppression) | 440 V nominal |
| Duty Cycle | 1 Hz |
| Switching Power | 1500 VA / 144 W (DC) |
| Peak Blocking Voltage | 250 VAC @ 360 Vpk |
| Channel-to-channel isolation | 300 VAC (1500 V transient) |
| Logic Side Ratings | |
| Pickup Voltage | 1 V @ 2 mA |
| Dropout Voltage | 4 VDC |
| Control Resistance | 220 ohms |
| Logic Supply Voltage | 5 VDC ± 0.25 VDC |
| Logic Supply Current | 160 mA maximum |
| Module Ratings | |
| Number of Channels Per Module | 4 |
| Turn-on Time | 8 milliseconds |
| Turn-off Time | 8 milliseconds |
| Torque, hold-down screws | 4 in-lb (0.45 N-m) |
| Torque, connector screws | 5.26 in-lb (0.6 N-m) |
| Operation Temperature | -20 to 70 °C |
| Storage Temperature | -30 to 85 °C |
| Agency Approvals | UL, CE RoHS, DFARS |
| Mechanical Life | 10 x 106 operations |
| Operational Life | 30 x 103 operations |
| Warranty | 30 months |
